收藏本站
9XTend ‐ PKG ‐ E? ? Ethernet ? RF ? Modem ? – ? Product ? Manual ? v2.x4x ? [2007.01.04]
KY (AES Encryption Key) Command
<Networking & Security> The KY command is
used to set the 256-bit AES (Advanced Encryption
Standard) key for encrypting/decrypting data.
Once set, the key cannot be read out of the
modem by any means. The entire payload of the
packet is encrypted using the key and the CRC is
computed across the ciphertext. When encryption
is enabled, each packet carries an additional 16
bytes to convey the random CBC Initialization
AT Command: ATKY
Binary Command: 0x3C (60 decimal)
Parameter Range:
0 - (any other 64-digit hex valid key)
Default Parameter Value: 0 (disabled)
Number of bytes returned: 2
Number Base: Always Hexadecimal
Vector (IV) to the receiver(s). The KY value may
be “0” or any 256-bit value (= 64 hex digits = 32 bytes). Any other value, including entering ATKY
by itself with no parameters, causes an error.
A modem with the wrong key (or no key) will receive encrypted data, but the data driven out the
serial port will be meaningless. Likewise, a modem with a key will receive unencrypted data sent
from a modem without a key, but the output will be meaningless. Because CBC mode is utilized,
repetitive data appears differently in different transmissions due to the randomly-generated IV.
LH (Wake-up Initializer Timer) Command
<Sleep (Low Power)> The LH Command is used
to set/read the duration of time during which the
wake-up initializer is sent. When receiving
modems are in Cyclic Sleep Mode, they power-
down after a period of inactivity (as specified by
the ST parameter) and will periodically wake and
listen for transmitted data. In order for the
receiving modems to remain awake, they must
detect ~35ms of the wake-up initializer.
LH Command must be used whenever a receiving
AT Command: ATLH
Binary Command: 0x0C (12 decimal)
Parameter Range: 0 - 0xFF
[x 100 milliseconds]
Default Parameter Value: 1
Number of bytes returned: 1
Related Commands: HT (Time before Wake-up
Initializer), SM (Sleep Mode), ST (Time before
Sleep)
modem is operating in Cyclic Sleep Mode. The
Wake-up Initializer Time must be longer than the cyclic sleep time that [as determined by SM
(Sleep Mode) parameter]. If the wake-up initializer time were less than the Cyclic Sleep interval,
the connection would be at risk of missing the wake-up initializer transmission.
Refer to figures loated under the SM command description to view diagrams of correct and incor-
rect configurations. The images emphasize that the LH value must be greater than the SM value.
MD (RF Mode) Command
<Networking & Security> The MD command is
used to select/read the settings that enable the
Polling and Repeater Modes on the modem.
Polling Mode - A ‘Polling Base’ is responsible for
polling remotes. A ‘Polling Remote’ requires a poll
AT Command: ATMD
Binary Command: 0x31 (49 decimal)
Parameter Range: 0 - 6
Parameter Configuration
in order to transmit.
Repeater Mode - A ‘Repeater’ re-sends RF data
unless the transmission is addressed to it or if the
transmission has already been detected. A
‘Repeater End Node’ handles repeated messages,
but will not repeat the message over-the-air.
0
1
2
3
4
Transparent Operation
(Repeater Base)
[reserved - not used]
[reserved - not used]
Polling Base
Polling Remote
Refer to the Polling and Repeater Mode sections of
the ‘RF Communication Modes’ chapter for more
information.
5 Repeater
6 Repeater End Node
Default Parameter Value: 0
Number of bytes returned: 1
Minimum Firmware Version Required: 2.x20
? ? 2007 ? MaxStream, ? Inc., ? Confidential ? & ? Proprietary ?‐? All ? Rights ? Reserved ?
????? 31
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
XT09-SI MODULE RF 900MHZ 1W 115K W/RPSMA
XU-A11 X-STICK 2.4GHZ USB TO XBEE
XV-8000CB :3 50.3000KHZ+/-60DPS AUTOMOTIVE GYRO SENSOR +/-60DPS
YB03WKW01-6B-JB INDICATOR PB RECT WHT LED ILLUM
YGM1 C518 THERM PTC MINI-BEAD 3MM 180C
YQD120N0006 THERMISTOR PTC OCP 6 OHM 25C
Z4D-A01 PHOTO SENSOR 7.5MM REFLECT TYPE
ZALM-301-1C-B RF TRANSCEIVER 100MW MMCX W/CONN
相关代理商/技术参数
XT09-PKI-E-NA 功能描述:射频模块 9XTend 1W Ethernet w/o accessories Intl RoHS:否 制造商:Linx Technologies 产品:Transceiver Modules 频带:902 MHz to 928 MHz 输出功率:- 15.5 dBm to + 12.5 dBm 接口类型:UART 工作电源电压:- 0.3 VDC to + 5.5 VDC 传输供电电流:38.1 mA 接收供电电流:22.7 mA 天线连接器类型:U.FL 最大工作温度:+ 85 C 尺寸:1.15 mm x 0.63 mm x 0.131 mm
XT09-PKI-R 功能描述:射频模块 9XTend 1W RS232/485 w/o accessories RoHS:否 制造商:Linx Technologies 产品:Transceiver Modules 频带:902 MHz to 928 MHz 输出功率:- 15.5 dBm to + 12.5 dBm 接口类型:UART 工作电源电压:- 0.3 VDC to + 5.5 VDC 传输供电电流:38.1 mA 接收供电电流:22.7 mA 天线连接器类型:U.FL 最大工作温度:+ 85 C 尺寸:1.15 mm x 0.63 mm x 0.131 mm
XT09-PKI-RA 功能描述:射频模块 900MHz - Xtend software setable RoHS:否 制造商:Linx Technologies 产品:Transceiver Modules 频带:902 MHz to 928 MHz 输出功率:- 15.5 dBm to + 12.5 dBm 接口类型:UART 工作电源电压:- 0.3 VDC to + 5.5 VDC 传输供电电流:38.1 mA 接收供电电流:22.7 mA 天线连接器类型:U.FL 最大工作温度:+ 85 C 尺寸:1.15 mm x 0.63 mm x 0.131 mm
XT09-PKI-RA-NA 功能描述:射频模块 9XTend 1W RS232/485 w/accessories no AES RoHS:否 制造商:Linx Technologies 产品:Transceiver Modules 频带:902 MHz to 928 MHz 输出功率:- 15.5 dBm to + 12.5 dBm 接口类型:UART 工作电源电压:- 0.3 VDC to + 5.5 VDC 传输供电电流:38.1 mA 接收供电电流:22.7 mA 天线连接器类型:U.FL 最大工作温度:+ 85 C 尺寸:1.15 mm x 0.63 mm x 0.131 mm
XT09-PKI-RDA 功能描述:射频模块 XTend-PKG 900 MHz IndRS-232class1/div2 RoHS:否 制造商:Linx Technologies 产品:Transceiver Modules 频带:902 MHz to 928 MHz 输出功率:- 15.5 dBm to + 12.5 dBm 接口类型:UART 工作电源电压:- 0.3 VDC to + 5.5 VDC 传输供电电流:38.1 mA 接收供电电流:22.7 mA 天线连接器类型:U.FL 最大工作温度:+ 85 C 尺寸:1.15 mm x 0.63 mm x 0.131 mm
XT09-PKI-R-NA 功能描述:射频模块 9XTend 1W RS232/485 w/o accessories Intl RoHS:否 制造商:Linx Technologies 产品:Transceiver Modules 频带:902 MHz to 928 MHz 输出功率:- 15.5 dBm to + 12.5 dBm 接口类型:UART 工作电源电压:- 0.3 VDC to + 5.5 VDC 传输供电电流:38.1 mA 接收供电电流:22.7 mA 天线连接器类型:U.FL 最大工作温度:+ 85 C 尺寸:1.15 mm x 0.63 mm x 0.131 mm
XT09-PKI-R-NL 制造商:Digi International Inc 功能描述:MODEM RF 900MHZ 9600/11
XT09-PKT-R 功能描述:MODEM RF 900MHZ RS232/485 RoHS:是 类别:RF/IF 和 RFID >> RF 接收器、发射器及收发器的成品装置 系列:XTend™ 标准包装:5 系列:MultiModem® iCell 功能:收发器，HSPA，调制解调器 调制或协议:GPRS，GSM，EDGE 频率:850MHz，900MHz，1.8GHz，1.9GHz 应用:- 接口:RS-232，USB 灵敏度:- 功率 - 输出:- 数据传输率 - 最大:7.2 Mbps 特点:- 电源电压:9 V ~ 32 V，USB 其它名称:881-1125